Extensions for Robot MOVE:Mini Mk2

Line tracking

Now you can add line tracking to: MOVE mini Mk1 and Mk2 with the Line tracking extension for: MOVE mini. Build it, code it, watch it go!

Add line tracking functionality to the MOVE mini for the BBC micro: bit with this easy to assemble add-on kit.

This add-on comes with all the parts needed to add line tracking functionality to the: MOVE mini and requires no soldering. Once built, the sensitivity of the left and right sensors can be individually adjusted to ensure smooth operation.

By default, the code will cause the buggy to follow a dark line on a light background but the code can be modified to do the opposite.

There is no need for soldering but the kit requires mechanical assembly.

Features

• Add line tracking features to the: MOVE mini for the BBC: BBC bit

• Can either track a dark line on a light background or a light line on a dark background

• Line sensitivity can be adjusted with a screwdriver

• No soldering required

• Following code example of line is provided

Contents

• MOVE Sensor Interface for the Micro:Bit BBC

• MOVE Line Next card for the Micro:Bit BBC

• Connector cable

• 2 x CS screws M3 8mm

• 2 x M3 full width hexagon screws

• 5 x CS M3 12mm screws

• 2 x 5 PCB pin sockets

• 1 x small Kitronik key ring

Bulldozer

With this Bulldozer add-on for: MOVE mini for the BBC microbit, everyone's favorite little programmable robot buggy just got better. Robots often do more than just get from A to B.

Although this extension was designed to work with: MOVE mini MK2, it can also be installed on the original: MOVE mini.

Previously on: MOVE mini, we; drew shapes, controlled it via bluetooth, controlled it with a second microbit, and also coded a variety of light shows. Now it can totally lift and carry things too!

This self-assembling bulldozer kit is made from the same materials as: MOVE mini, designed in accordance with the aesthetic MOVE mini, and also comes with the servo needed to move the bulldozer add-on up and down.

There is a very simple Servo: Lite card hack that allows control of the third servo, you can find how here. Once the kit is fully assembled, the bulldozer arm can be coded with the Microsoft MakeCode editor.

Note: To use this accessory, you must enable the third servo feature to be able to connect the third servo to the Servo: Lite board, a solder is required for this. The header pins required for this are provided with this kit. Also, enabling the third servo disables the on-board ZIP LEDs. If you cancel the third servo hack and return the board to its original state, the on-board ZIP lights will be re-enabled. We have produced a short guide showing how to enable the third servo and how to reverse this change, read it here.

Note

• This kit requires mechanical assembly

• This kit requires some soldering

Features

• When attached to: MOVE mini, this kit offers a fun introduction to the world of DIY robotics

• Code it with the Microsoft MakeCode editor

• Use in conjunction with an application and control it via Bluetooth

• Use the radio function and a second microbit as controller

Contents

• Buldozer parts kit

• Mini 180° servo

• 4 x M2 6mm steel pan head screws

• 4 x M2 full width hex nuts

• 2 x M3 recessed screw

• 3 x straight PCB pin sockets (the same type of pin as these pins)

Dimensions

• Length: 110mm

• Width: 50mm

• Height: 75mm

Bumper

Get more from: MOVE mini for the BBC microbit with the Bumper extension. Use the MOVE mini in a football/hockey game and play against other robots!

With this Bumper add-on for: MOVE mini for the BBC microbit, everyone's favorite little programmable robot buggy just got better. If you've been looking for an add-on that allows for competitive games, then this is the add-on for you.

Previously on: MOVE mini, we drew shapes, controlled it via bluetooth, controlled it with a second microbit, and also coded a variety of light shows. Now it can be totally used to play ball games too!

This self assembly bumper kit is made from the same materials as: MOVE mini and was designed in accordance with the: MOVE min.

Once the add-on has been attached to: MOVE mini, the buggy can now be easily used for competitive games involving a ball or puck, soccer and field hockey in mind.

Note

• This kit requires a mechanical assembly

Features

• This attachment can be assembled quickly and easily

• MOVE mini will be able to move balls and objects

• Allows for competitive team games such as soccer and field hockey

Contents

• Set of bumper parts

• Counter 2 x 10mm cast M3 screws

Dimensions

• Length: 32mm

• Width: 77mm

• Height: 9mm