- On sale!
- ODROID-H3 and ODROID-H3+, 64bit x86 single board computers equipped with Intel Jasper Lake 10nm processors: Celeron N5105 (H3) or Pentium N6005 (H3+)
- Ideal boards to build your own custom machine, with the addition of RAM (up to 64GB) and storage to suit your projects!
- Supports eMMC, PCIe Gen3 NVMe SSDs, and has plenty of I/O
- Totally passive operation with built-in passive heat sink
Contents
ODROID-H3 or ODROID-H3+ card depending on the version you choose
Warning: You must add memory to the card to use it.
Accessories needed to operate the card
- RAM
DDR4 SO-DIMM only (DDR3/DDR5 not supported)
- DC power supply
DC 15V/4A up to 60W recommended if not using two 3.5" hard drives
DC 19V/7A up to 133W recommended if using two 3.5" HDDs
Additional accessories
- EMMC module
- SDD Module
NVMe SSD and HDD/SSD compatible only (M.2 SATA SSD not supported)
- Wi-Fi/Bluetooth Module
5BK module or Miniature Wi-Fi module
- Protective casing
Caution: ODROID H3/H3+ cards do not support hot-plugging of storage devices (SATA, eMMC or NVMe): please do not replace your storage devices while the system is powered on as this may cause damage to the card and the devices
Features
-
ODROID-H3 : Intel Celeron N5105 Quad-Core 2 to 2.9 GHz with Intel UHD 24 RPM GPU 450 to 800 MHz
-
ODROID-H3+: Intel Pentium N6005 Quad-Core 2 to 3.3 GHz with Intel UHD 32 RPM GPU 450 to 900 MHz
-
Dual channel DDR4 PC4-23400 (2933MT/s) memory supporting up to 64 GB of RAM in total
-
EMMC module slot
-
M.2 slot (PCIe 3.0x4 for NVMe, supports NGFF-2280 cards)
-
x2 SATA3 6.0 Gb/s (JST-XH compatible SATA power connectors)
-
x24 GPIO pins with I2C, UART (3.3 V)
-
x2 USB 3.0
-
x2 USB 2.0
-
HDMI 2.0 (up to 4K @ 60Hz)
-
DisplayPort 1.2 (up to 4K @ 60Hz)
-
x2 Ethernet RJ45 (10/100/1000/2500 Mbps)
-
Passive heat sink
-
Power/reset switch
-
Battery backup connector (2-pin)
-
Active cooling fan connector (4-pin, 2.54mm pitch)
-
Audio output (3.5mm jack) and SPDIF, audio input (3.5mm jack)
-
SSE4.2 gas pedal (SMM, FPU, NX, MMX, SSE, SSE2, SSE3, SSSE3, SSE4.1, SSE4.2, AES)
-
DC power supply: outer diameter (negative) 5.5 mm, inner diameter (positive) 2.1 mm - 14V to 20V DC
-
x5 System LED indicators
-
Turbo boost mode for sustained processor performance
-
fTPM (TPM 2.0) enabled
-
50 seconds are required for BIOS boot
-
Dimensions: 110 x 110 x 47 mm
Useful documentation
Getting started with H3,H3+ boards
HARDWARE diagram
Video
Data sheet
- Category
- Nanocomputers
- Brand
- Odroid
- Connectivity
- I2C*~GPIO*~UART
- Type of storage
- SSD*~HDD*~eMMC
- Storage capacity
- 64 GB
- Number of LEDs
- x 5
- Processor (CPU)
- Intel® Pentium® N6005 Quad-Core 2.0 ~ 3.3 GHz*~Intel® Celeron® N5105 Quad-Core 2.0 ~ 2.9 GHz
- Graphics Processor (GPU)
- Intel® UHD Graphics® 24EUs, 450-800MHz*~Intel® UHD Graphics® 32EUs, 450-900MHz
- USB port(s)
- x 4
- USB 2.0 port(s)
- x 2
- USB 3.0 port(s)
- x 2
- Video / audio output(s)
- 3.5mm stereo jack
- Ethernet port(s)
- Gigabit Ethernet
- Headphone jack
- Stereo Jack
- Type of product
- Monocard
You might also like
Customers who bought this product also bought:
Questions (0)
No customer questions for the moment.