HAT engine compatible Raspberry Pi, Jetson Nano Embeds x40 PIN GPIO 6 microstep modes available, configured with DIP switches: full step, half step, 1/4 step, 1/8 step, 1/16 step and 1/32 step Ideal for 3D printer projects, sculpting machine, mechanical arm...
Have a fun and creative learning experience with LEGO® and Raspberry Pi Raspberry Pi Build HAT add-on board with a Raspberry Pi RP2040 microcontroller designed in collaboration with LEGO® Education and compatible with all LEGO® models Raspberry Pi Control up to 4 LEGO® extensions such as...
Designed for Raspberry Pi Pico, ideal for robotic projects Allows Raspberry Pi Pico to drive 4 motors simultaneously or 2 stepper motors 27 I/O pins available to add other devices such as sensors, LEDs, etc. Equippedwith an on/off switch and a power status LED
Motor driver for Raspberry Pi Pico, ideal for buggy projects Allows Raspberry Pi Pico to drive two motors simultaneously or a single stepper motor Includes DRV8833 motor driver IC with short circuit, overcurrent and heat protection Éequipped with an on/off switch and a power status LED
Mini mechanical keyboard kit with 16 clickable keys (4x4) for self-assembly (no soldering) Low-latency input and high reliability with the RP2040 microcontroller Raspberry Pi Equipped with Kailh Speed switches and intelligent transparent DSA keys with fully customizable RGB lighting...
LONGRUNNER stepper motor with standard interface and servo motor included Compatible with 2560, 1280 DSP, STM32, Raspberry Pi and Arduino IDE LK67 4-phase LED A, B, C, D indicates the operating status of the stepper motor. Pull-up torque: > 34.3 mN.m (120 Hz); Unwind torque: > 34.3...
Drive two DC motors simultaneously Specially designed for Raspberry Pi, this Motor Driver HAT allows you to drive two DC motors at the same time. Controlled via an I2C interface, this accessory is ideal for your intelligent mobile robots.
Expansion module to simplify robotics projects Wide range of connectors: 7 Grove connectors, x2 PIN connectors with silk-screen printing for easy connection Integrated DC motor driver, designed to manage either 2 brush DC motors, or a single bipolar/unipolar stepper motor, and even 4 servomotors...
Needless to say, the Raspberry Pi is quite powerful in most cases, but it is not very good at providing accurate PWM output. You may have tried to control a robotic arm or hexapod using the Pi, but are ultimately frustrated because of the limited number of PWM outputs and servo jitter. Now that...
Motor driver card ideal for mobile robots Équiped with 4 LED lights and 4 test buttons Regenerative braking provides better control of motor speed Compatibility with Arduino and Raspberry Pi and micro:bit controllers
An RGBW-lit, clickable switch card, perfect for adding navigation or control to your projects Raspberry Pi or Arduino.
This is a pan-tilt kit designed for Raspberry Pi. With the integrated PCA9685 PWM chip and TSL2581 ambient light sensor, it allows the Pi to control camera movement and detect light intensity via the I2C interface.
This Pan-Tilt Kit is the perfect way to give your project a full range of programmable motion. The pan-tilt can rotate approximately 180° from side to side and can tilt up and down around 150°. Comes in a kit with two included 38mm x 36mm micro servo motors (GS-90 or GS-92 Type) and space to...
CAN RS485 isolated extension HAT 1 CAN channel : MCP2515 controller with CAN transceiver 2 RS485 channels: SC16IS752 and SP3485 dual chip combination Standard 40PIN GPIO header Raspberry Pi
This ADS1015 ADC (analog-to-digital converter) package has three channels that can read voltages from -24 V to +24 V at sampling rates up to 3.3 KHz with 12-bit resolution. It is compatible with Raspberry Pi and Arduino and is ideal for measuring voltages quickly and accurately over a wide...
Breakout navigation module ideal for surface detection and floor tracking of a robot vacuum cleaner PAA5100JE sensor that uses a low-resolution camera and intelligent algorithms to detect surface movement Very narrow range of 15 to 35 mm, suitable for use with a wide variety of...
Feetech / FITEC 9g Micro Servo Analog servo with 360 degrees continuous rotation 6 V - 1.5 kg / cm Ideal for model making and D.I.Y, to create a radio controlled device (helicopters, planes, drones, robots, cars, ...)
DC motor ideal for robotics, model making, ... Reduction ratio: 1/48, 1/120, 1/180, 1/220, 1/256, 1/288, Load current: 0.1-0.35A
Geekservo 2kg 360° motor Compatible with the famous brick building set Suitable for medium and large projects Dual 360° output axes
Geekservo 2kg 360° servo motor Suitable for medium and large projects Compatible with lego Dual 360° output axes
HighqualityGeekservo motor Compatible with the famous brick building game Programmable with Makecode Javascript, microPython, C++ Operating voltage from 3.3 to 6V
Ideal for a mini video surveillance system, this set of horizontal and vertical motion servos will give you the movement of the Pi camera with a minimum of fuss.Pan-Tilt HAT allows you to mount and control one of our panoramic modules right on top of your Raspberry Pi. The HAT and its on-board...
Français
Español
Italiano
Deutsch
Portugais
