Connectivity Raspberry Pi, compatible with Raspberry Pi Zero / Zero W / Zero WH / 2B / 3B / 3B + / 4 CAN function, integrated CAN controller MCP2515 via SPI interface, integrated transceiver SN65HVD230 RS485 function, controlled via UART, half-duplex communication, supports automatic TX / RX...
Increase the capabilities of your Raspberry Pi The original Raspberry Pi has only one UART port with 1 channel. With this serial extension, you have a UART with two channels as well as 8 GPIOs programmable via I2C. The LEDs integrated in the extension allow you to monitor the UART operating status.
Choose the best camera The quality of the OV5640 image sensor is very good thanks to its 5 megapixels and its high performance. Among its various strengths, this camera module supports DVP and MIPI interfaces as well as the CSI serial interface.
This set of lenses has everything to become the ideal accessory for your Camera Module for Raspberry Pi! Switch lenses as the situation changes to shoot with your Pi in new ways! Package:1 x Fisheye Lens1 x 0.63x Wide Angle Lens1 x 0.36x Wide Angle Lens1 x 15x Macro Lens1 x 20x Macro Lens1 x...
Connect all your cameras In order to use all your cameras Arducam-Mini, the adapter card Arducam offers you the possibility to use them on a single microcontroller. This multi-camera board is fully compatible with Raspberry Pi, Arduino and BeagleBone Black. Simple and open source, all you need...
High performance camera in a small package The Arducam Mini Module Camera Shield 5 MP Plus OV5642, is an easy-to-use high-definition camera with great performance. Reducing the complexity of the camera control interface, this mini module also features an open source code library. Thanks to its...
This camera supports night vision and can focus accurately. It is equipped with oV5647 Pi 5 megapixel sensor. Supports the connection of infrared LEDs and/or LED flash.
Engine: 1. Voltage: DC 3V - 6V 2. 100 mA - 120mA 3. Reduction ratio: 48 : 1 4. Rpm (with tires) : 100-240 5. Tire diameter : 65mm 6. Car speed ( m / minute ) : 20-48 7. Engine weight ( g ) : 29 / each 8. Engine size: 70mm x 22mm x 18mm Tire:1. Center hole: 5.3mm x 3.66mm 2. Wheel...
Compatible with Raspberry Pi A, B, A+, B+, Zero, 2, 3 with its L80-39 GPS chipCommunicates satellite data via UART or USBCP2102 as a stable and faster UART chip USB bridge66 simultaneous search channels and 22 tracking channelsAdvanced AGPS EASY™ technology without external memory USB cable not...
The RemotePi card is an infrared remote control with on/off button. This card is mainly unitlised on a media center or emulator, LibreELEC, OpenELEC, OSMC, XBian, RasPlex, Raspbian, Volumio, RetroPie, Recalbox ... This infrared remote control will allow you to navigate through the menus of your...
Add a tracker to your Raspberry For an optimal use of your Raspberry Pi, you can install a tracking module. This infrared reflection sensor can be used for: electricity meter, paper detection in printer, barrier detection, black and white line detection..
Raspberry Pi + LoRa (TM) expansion board with HopeRF LoRa (TM) radio module(s) installed. Comes with appropriate manifold and spacers, SMA and modules installed. The first module purchased will be installed in slot CE1, the second in slot CE0. If you plan to use this board in conjunction with...
It is a low power HAT Raspberry Pi, equipped with multiple communication features: GSM, GPRS, GNSS and Bluetooth. It allows your Pi to easily make a phone call, send messages, connect to the Internet wirelessly, global position, transfer data via Bluetooth, and so on. GPS antenna not included.
USB HUB x4 ports designed for Raspberry Pi Zero/Zero 2W/Zero W/Zero WH Pogo pins for direct connection to Pi Zero boards x4 USB ports, USB2.0 / 1.1 compatible Supplied with screw kit
This expansion board connects to a Raspberry Pi Zero or Zero W via pogo pins to provide a full-size USB Type-A connector.You can turn a Raspberry pi zero or Raspberry pi zero W into a U drive via the P4wnP1 project (https://github.com/mame82/P4wnP1), and also use it as a BadUSB device)....
To take beautiful shots with your camera Raspberry Pi, this tripod will help you to place your module in every corner! Compatible with v2 Camera Modules Raspberry Pi (does not support the official v3 camera module factor) Camera stand not included.
High capacity servo with all metal gears and 1 bearing Comes with 3 servo arms Features : Weight : 13.4grs Dimensions: 22.8x12.2x28.5 mm Torque : 1.8kgs(4.8V)/2.2kgs(6V) Speed : 0.1sec/60degrees (4.8v)/ 0.08sec/60degrees(6V) Operating voltage : 4.8V/ 6V Operating temperature: 0 /+55°
Multifunctional GPIO expansion card for Raspberry Pi 3.
Boost your Raspberry Pi 5 by adding an NVMe SSD for lightning-fast performance! The official M.2 HAT+ allows you to connect M.2 (M-Key) devices to the Raspberry Pi 5's PCIe connector using the included cable 4 Gbps PCIe 2.0 interface for fast data transfer (~500Mbytes/s) to and from...
HAT+ for Raspberry Pi 5, compatible with M.2 SSD size 2230 and 2242 Supports PCIE X1 Gen2 only, does not support booting Pi 5 from SSD Dual Built-in LED Indicators for operational status monitoring HAT+ design with integrated EEPROM chip
Français
Español
Italiano
Deutsch
Portugais
