Isolated relay HAT card Has one two-channel input and one two-channel output Up to 24V DC or 250V AC at 10A Design makes it easy to connect to cards Arduino
CAN RS485 isolated extension HAT 1 CAN channel : MCP2515 controller with CAN transceiver 2 RS485 channels: SC16IS752 and SP3485 dual chip combination Standard 40PIN GPIO header Raspberry Pi
The board features an integrated battery holder, ideal for powering your Micro:bit for mobile projects x4 3-pin ports with 2.54 mm pitch for connecting various modules Features a servomotor control interface, enabling precise motion control for a variety of robotic applications Includes a...
Allows precise adjustment of output voltage and current over a wide input voltage range from 6V to 40V and converting 24V to 12V Efficiency up to 96% and measured at 20A Stable and reliable Quality and durable finish
Li-ion battery charger/switch with dynamic power path management for more stable power supply I2C bus communication, real-time monitoring of voltage, current, power and remaining battery capacity Multi-battery protection circuits: overcharge/discharge protection, overcurrent protection, short...
Switching power supply AC 100-240V to DC 5V 5A 60W anti-interference and high reliability Wide input voltage range (100-240V) in accordance with the worldwide operating standards Good insulation performance and high electrical resistance 85% efficiency
Allows precise adjustment of output voltage and current over a wide input voltage range of 0 to 40V and an adjustable output voltage of 1.25V-37V Efficiency up to 92% andmaximum output current up to 3A Integrated LCD display
Connectivity Raspberry Pi, compatible with Raspberry Pi Zero / Zero W / Zero WH / 2B / 3B / 3B + / 4 CAN function, integrated CAN controller MCP2515 via SPI interface, integrated transceiver SN65HVD230 RS485 function, controlled via UART, half-duplex communication, supports automatic TX / RX...
Compatible with port: ATX (compatible with partial BTX type) PIN number: 24-pin Switch: Yes Number of output sets: four sets of different voltage Size: 12.8 x 4.8 cm / 5.04 x 1.89 "
AC-DC 4A to 6A 24V switching power supply module Overvoltage and overcurrent protection Converts output between AC and DC 100W output power
The 12V 16-CH relay is capable of controlling various devices and other equipment with high current. It can be controlled directly by a microcontroller. Each one needs a pilot current of 15 to 20 mA; Equipped with high current relays, AC250V 10A; DC30V 10A; Standard interface can be controlled...
The RV3028 RTC breakout is perfect for adding timing to your project and, thanks to the small built-in battery, will keep time when your device is turned off. The tiny silver oxide battery (8mAh, included) keeps the RTC running when your device (Raspberry Pi or Arduino) is turned off and can...
Real time clock with battery to keep time even when your project is off or while you reprogram your microcontroller. The breakout is perfect for time dependent projects, timers, alarms, etc. The DS1307 is the most popular RTC, and works perfectly with 5V microcontrollers such asArduino. This...
This fully isolated, I2C-controllable switch can switch large loads up to 40 V at 10 A.
RTC Shield for ODROID-C2 Simply mount this RTC Shield on the ODROID-C2's GPIO port to keep track of when your ODROID is offline. A lithium battery can keep the RTC chip working for 5 to 6 years without external power. You can still use the official ODROID case with this shield. Features : Size:...
Power: bit is a type of micro: bit expansion card of minimal size. It is powered by two 2025 button batteries and has a buzzer on the card.
For a discreet, sleek and tidy power supply solution, the Zero LiPo will help you provide the most compact power supply at Raspberry Pi. You can either solder the 0.8mm thick PCB directly to the bottom of your GPIO header for a permanent solution or solder to the included 2x4 0.1" female header...
Français
Español
Italiano
Deutsch
