Switching power supply AC 100-240V to DC 5V 5A 60W anti-interference and high reliability Wide input voltage range (100-240V) in accordance with the worldwide operating standards Good insulation performance and high electrical resistance 85% efficiency
Control high voltage devices The RPi Relay Board is an expansion board for Raspberry Pi that has 8 channels. This high voltage relay expansion board allows you to remotely control various products such as connected household appliances. Thanks to the on-board LEDs, you can follow the status of...
Motor driver card ideal for mobile robots Équiped with 4 LED lights and 4 test buttons Regenerative braking provides better control of motor speed Compatibility with Arduino and Raspberry Pi and micro:bit controllers
HAT network extension with antennas for Raspberry Pi (GPIO - 40 PIN) Support for 5G / 4G / 3G networks, Multi-Band / Multimode Based on Qualcomm Snapdragon X55 platform SIM card slot, supports 1.8 V / 3 V SIM card
Connectivity Raspberry Pi, compatible with Raspberry Pi Zero / Zero W / Zero WH / 2B / 3B / 3B + / 4 CAN function, integrated CAN controller MCP2515 via SPI interface, integrated transceiver SN65HVD230 RS485 function, controlled via UART, half-duplex communication, supports automatic TX / RX...
Base board for Raspberry Pi Compute Module 4 Nano A is a mini compute module board Raspberry Pi With x40 GPIOs, you can connect various HAT modules Embeds various ports such as: USB, microSD and MIPI CSI
Expansion board compatible with the ESP32 Core keyestudio card Designed to expose all keyestudio ESP32 Core board pins as a 2.54mm pin header Embedded DIP switch for power control Powered via DC 7-12V socket
The TV HAT allows you to receive and decode digital television (DTT) streams on your Raspberry Pi via its built-in DVB-T2 tuner. Then you can watch these streams on any computer connected to the same network as the Pi. It is recommended to use it with a Raspberry Pi 2, 3, 3+ or higher for...
Low Noise Amplifier Modules (LNA) based on SAW bandpass filter Designed to pass between a software defined radio receiver and an antenna and reduce out-of-band intermodulation while providing additional gain for increased sensitivity Compatible with most USB SDR dongles such as RTL...
Discover your HDMI Mini Decoder card! So small and so simple, you can use this card as an all-in-one driver for TTL displays, or to decode HDMI / DVI video. This is the contact version! So you can combine it with to a resistive touchscreen! This driver is specifically designed for compact...
Extension with multiple sensors (temperature, humidity, magnetometer…), a 64x64 LED matrix, and a mini joystick. Designed for measurements, experiments and Python programming Easily connects to the Raspberry Pi via the 40 GPIO pins Compatible with the Raspberry Pi 5, as well as...
Compatible with most Nano boards Arduino Nano, ideal for small microcontroller projects, Compact board with all Maker UNO features, Easy learning and debugging with on-board LEDs, 5V regulator included (power your circuit from a battery or DC adapter, in addition to the USB...
Drive two DC motors simultaneously Specially designed for Raspberry Pi, this Motor Driver HAT allows you to drive two DC motors at the same time. Controlled via an I2C interface, this accessory is ideal for your intelligent mobile robots.
Board designed to add connectivity to your CM4 (x2 Gigabit Ethernet ports) and connectivity (USB, x40 GPIO pins,...) Enclosure included, robust metal design with excellent heat dissipation Removable magnetic GPIO cover Perfectly suited for industrial applications
Needless to say, the Raspberry Pi is quite powerful in most cases, but it is not very good at providing accurate PWM output. You may have tried to control a robotic arm or hexapod using the Pi, but are ultimately frustrated because of the limited number of PWM outputs and servo jitter. Now that...
It is a 2-channel RS232 expansion HAT designed for Raspberry Pi which adopts SC16IS752 + SP3232 solution, with built-in protection circuits such as power supply isolation, ADI magnetic isolation and TVS diode, etc.It is easy to control the 2-channel RS232 via SPI interface. With fast...
GSR (Galvanic Skin Response) sensor to reflect your emotions simply by placing two electrodes next to each other Ideal for monitoring sleep quality, lie detector, etc. Adjust sensitivity via potentiometer Easy-to-read analog voltage output
MEGA 2560 R3 and MEGA 2560 Plus microcontroller boards are based on ATMEGA2560 Equipped with the CP2102 USB serial chip Fully IDE compatible Arduino The major differences between the boards are: the voltage regulator chip, the addition of I/O and the USB port
FT232RL USB-C to UART (TTL) communication board Compatible with Mac OS, Linux, Android, WinCE, Windows 7/8/8.1/10/11... 3 power supply modes 5 V output, 3.3 V output or powered by the target board (3.3 V-5 V) Dimensions: 46 x 19 mm
CompatibleArduino UNO R3, Designed for school education, ideal for STEM projects, Simplified coding and electronics with built-in LEDs, Develops problem solving and stimulates creativity.
Expansion board specially designed for the Raspberry Pi 400 Angled GPIO socket header compatible with most of the modules for Raspberry Pi Ideal angle for reading a screen, a display, ... on Raspberry Pi 400 2 STEMMA connection ports (GPIO n°18 and 13) and 2 STEMMA QT I2C ports (cables not...
Designed for beginners and experts for electronics and programming projects Open hardware development board based on ATmega328P Ideal for building devices that interact with the real world, from everyday objects to scientific instruments 100% compatible Arduino Uno, works with...
GPIO expansion card to connect up to 4 expansion modules Designed specifically for the Raspberry Pi Pico Independent USB power input connector to provide power to multiple expansion modules Clear and easy to use pinout labels
Real time clock with battery to keep time even when your project is off or while you reprogram your microcontroller. The breakout is perfect for time dependent projects, timers, alarms, etc. The DS1307 is the most popular RTC, and works perfectly with 5V microcontrollers such asArduino. This...
Français
Español
Italiano
Deutsch
Portugais
