A very good environmental sensor ideal for indoor monitoring of temperature, pressure and humidity, or even outdoors in a suitable enclosure. It is compatible with Raspberry Pi and Arduino. If you are an iOS user, there is a Homebridge plugin for the BME280 to allow you to use the sensor for home...
Expansion board compatible with the ESP32 Core keyestudio card Designed to expose all keyestudio ESP32 Core board pins as a 2.54mm pin header Embedded DIP switch for power control Powered via DC 7-12V socket
This kit contains everything you need to take measurements with your card Arduino!
Six touch-sensitive buttons to use for whatever your heart desires, with additional LEDs; Touch pHAT has six capacitive touch buttons, each with a bright white LED, designed to be completely agnostic about their use. You can even use a dry erase pen to write on the pads to label their function....
LOT OF 4 LED - 2 infrared emitters 5mm and 2 receiver diodes Size: 5MM
AC-DC 4A to 6A 24V switching power supply module Overvoltage and overcurrent protection Converts output between AC and DC 100W output power
Detect six distinct channels of visible light with this spectral sensor. Unlike normal RGB color sensors, with the AS7262, you'll get six bands of color readings that roughly translate into red, orange, yellow, green, blue and violet. The two built-in white LEDs allow you to illuminate...
Capture the world around you with enviro:bit! It has sensors for air and weather, color and light, and sound, and connects directly to your micro: bit. Just place your micro: bit, then code enviro:bit with the block-based Microsoft MakeCode editor, or with MicroPython in the Mu code editor. The...
Install an ultraviolet sensor for your Raspberry Thanks to a Si1145 chip with integrated ADC, this sensor can detect ultraviolet but also the intensity of ambient light. This sensor directly emits the UV index value via the I2C interface.
HAT network extension with antennas for Raspberry Pi (GPIO - 40 PIN) Support for 5G / 4G / 3G networks, Multi-Band / Multimode Based on Qualcomm Snapdragon X55 platform SIM card slot, supports 1.8 V / 3 V SIM card
Base board for Raspberry Pi Compute Module 4 Nano A is a mini compute module board Raspberry Pi With x40 GPIOs, you can connect various HAT modules Embeds various ports such as: USB, microSD and MIPI CSI
Low Noise Amplifier Modules (LNA) based on SAW bandpass filter Designed to pass between a software defined radio receiver and an antenna and reduce out-of-band intermodulation while providing additional gain for increased sensitivity Compatible with most USB SDR dongles such as RTL...
To set up a lighting system in your different projects, choose this LED switch! Dimensions: 30x25x28mm 16A 250V 20A 125V
Expand your possibilities with an expansion board The MCP23017 IO expansion board allows to extend the 2 signal pins as 16 I2C controlled I/O pins. To increase the possibilities to the maximum, up to 8 MCP23017 IO expansion boards can be used at the same time to increase the number of I/O pins...
Discreet heat sink and fan keeps the CPU at a stable temperature for optimal performance 2-pin jumper wire for easy connection to your board's CN2 connectors Fan with thermal pad on the back (to be placed on the metal part of the board) Compatible with LattePanda V1 board
Connectivity Raspberry Pi, compatible with Raspberry Pi Zero / Zero W / Zero WH / 2B / 3B / 3B + / 4 CAN function, integrated CAN controller MCP2515 via SPI interface, integrated transceiver SN65HVD230 RS485 function, controlled via UART, half-duplex communication, supports automatic TX / RX...
These small boxes with clear lids are ideal for storing your small parts. The beauty of these boxes is that they also fit together in any configuration you choose. You can mix and match all sizes to create the perfect box for your needs and add more components if needed. Size: 25 x 32 x 22mm...
The RemotePi card is an infrared remote control with on/off button. This card is mainly unitlised on a media center or emulator, LibreELEC, OpenELEC, OSMC, XBian, RasPlex, Raspbian, Volumio, RetroPie, Recalbox ... This infrared remote control will allow you to navigate through the menus of your...
Make your Raspberry Pi 4 seriously cool with Fan SHIM! This seamless, 30mm controllable CPU fan with RGB LED and touch switch will give your Raspberry Pi significantly better thermal performance. It's quiet too! Note that due to the height of the fan, if you want to use HATs or pHATs with Fan...
Honeycomb-shaped digital LED module Red color LED x6 annotated ports for easy operation Compatible with micro:bit card (alligator clip connection)
Useful to connect your wires together Set of 20 electrical screw terminals with 5.08 mm connector
Ideal kit for simply extending the capabilities of your Micro:bit Includes x8 Grove modules (distance, light, gesture sensors, etc.) Easy connections thanks to the Grove connector, simply plug in modules without cables or soldering! Micro:bit BB V2 compatible (not included
These small boxes with clear lids are ideal for storing your small parts. The beauty of these boxes is that they also fit together in any configuration you choose. You can mix and match all sizes to create the perfect box for your needs and add more components if needed. Size: 76 x 32 x 22mm...
Français
Español
Italiano
Deutsch
Portugais
